qmk_firmware/keyboards/ferris/keymaps/pierrec83/config.h
Pierre Chevalier 704934c427
Ferris reorganization (#10564)
* Add my own keymap

* Layer 0: Workman
* Layer 1: RSTHD (my own take on it)
* Layer 2: Mouse
* Layer 3: Navigation
* Layer 4: Symbols right
* Layer 5: Symbols left
* Layer 6: Fn keys
* Layer 7: Numbers
* Layer 8: Vim and misceallaneaous accessible from any other layer

* Move the current code to a 0.1 folder in preparation for upcoming changes

Version 0.2 is currently being prototyped and uses an arm chip which
will need its own firmware.

There is also the Ferris sweep which uses a pro-micro compatible board
which will need its own directory.

* Move Ferris out of handwired and into the light

The keyboard is now well out of the prototype phase as tens of them have
been produced and acquired by various people.

With 0.2 coming out, adoption is going to increase again as the board
will be available for sale at some recognized vendors.

Now is probably a good time to recognize its status as more than a
prototype :)

* Add code for the Ferris Sweep (a.k.a cradio)

The Ferris Sweep is a creation of the talented @davidphilipbarr, a.k.a DPB.
It has the key layout of a Ferris and uses a pro-micro connected to the
switches via direct pins so that diodes are not needed and the soldering
is minimal.

With their blessing, I took the code for it from DPB's own repo:
https://github.com/davidphilipbarr/36keys/tree/master/qmk/cradio
and did some adaptations such as removing commented out code, enabling
EE_HANDS and mouse keys for consistency with my existing Ferris code.

* Fix indentation in rules.mk

* Fix indentation in sweep's config

* Remove unnecessary lines from sweep's rules.mk

* Remove unnecessary lines from sweep's rules.mk

* Rename 0.1 to 0_1

This avoids the dot looking like the separation between a filename and
its extension.

In the same commit, bring matrix.c to the 0_1 folder as this was needed
for the code to compile properly (matrix.c is referred to in the readme
under `0_1` and is specific to that revision of the firmware).

* Update copyright statements for Sweep
2020-10-17 12:20:34 -07:00

40 lines
1.6 KiB
C

/*
Copyright 2020 Pierre Chevalier <pierrechevalier83@gmail.com>
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#pragma once
// Set the mouse settings to a comfortable speed/accuracy trade-off,
// assuming a screen refresh rate of 60 Htz or higher
// The default is 50. This makes the mouse ~3 times faster and more accurate
#define MOUSEKEY_INTERVAL 16
// The default is 20. Since we made the mouse about 3 times faster with the previous setting,
// give it more time to accelerate to max speed to retain precise control over short distances.
#define MOUSEKEY_TIME_TO_MAX 40
// The default is 300. Let's try and make this as low as possible while keeping the cursor responsive
#define MOUSEKEY_DELAY 100
// It makes sense to use the same delay for the mouseweel
#define MOUSEKEY_WHEEL_DELAY 100
// The default is 100
#define MOUSEKEY_WHEEL_INTERVAL 50
// The default is 40
#define MOUSEKEY_WHEEL_TIME_TO_MAX 100
// Pick good defaults for enabling homerow modifiers
#define TAPPING_TERM 200
#define PERMISSIVE_HOLD
#define IGNORE_MOD_TAP_INTERRUPT
#define TAPPING_FORCE_HOLD