qmk_firmware/keyboards/maxipad/Makefile
climbalima 6e27f6fbde Changes to be committed:
new file:   keyboards/lets_splitv2/Makefile
	new file:   keyboards/lets_splitv2/config.h
	new file:   keyboards/lets_splitv2/i2c.c
	new file:   keyboards/lets_splitv2/i2c.h
	new file:   keyboards/lets_splitv2/imgs/split-keyboard-i2c-schematic.png
	new file:   keyboards/lets_splitv2/imgs/split-keyboard-serial-schematic.png
	new file:   keyboards/lets_splitv2/keymaps/default/keymap.c
	new file:   keyboards/lets_splitv2/lets_split.c
	new file:   keyboards/lets_splitv2/lets_split.h
	new file:   keyboards/lets_splitv2/matrix.c
	new file:   keyboards/lets_splitv2/pro_micro.h
	new file:   keyboards/lets_splitv2/readme.md
	new file:   keyboards/lets_splitv2/serial.c
	new file:   keyboards/lets_splitv2/serial.h
	new file:   keyboards/lets_splitv2/split_util.c
	new file:   keyboards/lets_splitv2/split_util.h
	new file:   keyboards/maxipad/Makefile
	new file:   keyboards/maxipad/config.h
	new file:   keyboards/maxipad/keymaps/default/Makefile
	new file:   keyboards/maxipad/keymaps/default/config.h
	new file:   keyboards/maxipad/keymaps/default/keymap.c
	new file:   keyboards/maxipad/keymaps/default/readme.md
	new file:   keyboards/maxipad/maxipad.c
	new file:   keyboards/maxipad/maxipad.h
	new file:   keyboards/maxipad/readme.md
2016-11-10 18:19:13 -05:00

76 lines
2.8 KiB
Makefile

# MCU name
#MCU = at90usb1287
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=512
# Build Options
# change yes to no to disable
#
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
CONSOLE_ENABLE ?= yes # Console for debug(+400)
COMMAND_ENABLE ?= yes # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
NKRO_ENABLE ?= no # USB Nkey Rollover
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default
MIDI_ENABLE ?= no # MIDI controls
UNICODE_ENABLE ?= no # Unicode
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE ?= no # Audio output on port C6
ifndef QUANTUM_DIR
include ../../Makefile
endif