qmk_firmware/keyboards/jd45/keymaps/mjt/rules.mk
Michael Terhar 7960302242 Keymaps for several of my boards (#1641)
* copied mjt keymaps from archive

* All mjt boards now compile

* fixed jd45-mjt breathing

* Updates to fix SpaceFN but not tested yet.

* Still missing either spacebar or an adjacent keypress.

* Debugging rigged up for use with hid_listen.

* Reverted the default keymap to use tap_layer_key rather than custom.  Moved custom approach to keymap_debug.c

* Fixed the lower-left side of the keymap, which needed more spacers due to the matrix being directly put into the array rather than using the keymap function.

* Cleaned up JD45 keymap that uses tapkey.

* Redid minivan keymap with numsym rather than raise/lower.
Untested.

* Created my MJT keymap for HHKB
Enabled dynamic macros and moved
somoe of the shortcuts around.

* Minor keymap fixes to make them compile without errors.

* Added home/end to right arrow cluster on DYN layer.

* Added more keys to fn and dyn layers.

* It wasn't using my custom layer last time somehow...?  Now it will.

* Compiled and installed at end of day on 8/23

* Moved macros to FKEY layer because Adjust was too hard to get into and out of without some sort of feedback.

* Fixed volume controls... were reversed and disabled.

* Added F13-F15 back to fkeys layer in Minivan

* Created new Planck Keymap that uses the NumSym and FKeys layer approach like the Minivan.

* Removed DYN layer.

* Fixed diagram in planck numsym.

* Cleanup for pull request.

* Roadkit flip phone warning.

* Replaced PLAY_NOTES_ARRAY to PLAY_SONG

* reset the submodules

* checked out specific commits for submodules

* Removed debugging from JD45 shared config.h

* Moved custom rules.mk to apropriate keymap

Reset the shared rules.mk file.

* Trailing return issue in rules.mk

Gotta make for a smooth pull request :-)
2017-08-26 23:33:33 -04:00

68 lines
2.6 KiB
Makefile

# MCU name
#MCU = at90usb1287
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options
# comment out to disable the options.
#
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = yes # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
MIDI_ENABLE = no # MIDI controls
# UNICODE_ENABLE = YES # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID