2423136788
The devicetree pulls always add on to the extra pulls configured by toggle mode, so these should not have pulls defined in the devicetree. Saved ~200uA avg on another board with a 3t toggle switch
141 lines
3.4 KiB
Plaintext
141 lines
3.4 KiB
Plaintext
/*
|
|
* Copyright (c) 2022 The ZMK Contributors
|
|
*
|
|
* SPDX-License-Identifier: MIT
|
|
*/
|
|
|
|
#include <dt-bindings/led/led.h>
|
|
#include <dt-bindings/zmk/matrix_transform.h>
|
|
|
|
&arduino_i2c {
|
|
status = "okay";
|
|
};
|
|
|
|
nice_view_spi: &arduino_spi {
|
|
status = "okay";
|
|
|
|
cs-gpios = <&arduino_header 16 GPIO_ACTIVE_HIGH>;
|
|
|
|
// Needed so the nice_view shield will enhance the existing node which falls *first*
|
|
// on the bus, properly picking up the first `cs-gpios` specifier.
|
|
ls0xx@0 {
|
|
reg = <0>;
|
|
};
|
|
|
|
led_strip: ws2812@0 {
|
|
compatible = "worldsemi,ws2812-spi";
|
|
|
|
/* SPI */
|
|
reg = <0>; /* ignored, but necessary for SPI bindings */
|
|
spi-max-frequency = <4000000>;
|
|
|
|
/* WS2812 */
|
|
chain-length = <7>; /* 4 underglow + 3 per-key LEDs */
|
|
spi-one-frame = <0x70>;
|
|
spi-zero-frame = <0x40>;
|
|
|
|
color-mapping = <LED_COLOR_ID_GREEN LED_COLOR_ID_RED LED_COLOR_ID_BLUE>;
|
|
};
|
|
};
|
|
|
|
/ {
|
|
chosen {
|
|
zmk,kscan = &kscan_matrix;
|
|
zmk,backlight = &backlight;
|
|
zmk,underglow = &led_strip;
|
|
zmk,matrix-transform = &matrix_transform;
|
|
};
|
|
|
|
// Commented out until we add more powerful power domain support
|
|
// external_power {
|
|
// compatible = "zmk,ext-power-generic";
|
|
// init-delay-ms = <200>;
|
|
// control-gpios = <&arduino_header 1 GPIO_ACTIVE_LOW>;
|
|
// };
|
|
|
|
rgb_power {
|
|
compatible = "zmk,ext-power-generic";
|
|
init-delay-ms = <200>;
|
|
control-gpios = <&arduino_header 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
backlight: gpioleds {
|
|
compatible = "gpio-leds";
|
|
gpio_led_0 {
|
|
gpios = <&arduino_header 12 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
matrix_transform: matrix_transform {
|
|
compatible = "zmk,matrix-transform";
|
|
rows = <3>;
|
|
columns = <4>;
|
|
|
|
map = <
|
|
RC(0,0) RC(0,1)
|
|
RC(1,0) RC(1,1)
|
|
>;
|
|
};
|
|
|
|
direct_matrix_transform: direct_matrix_transform {
|
|
compatible = "zmk,matrix-transform";
|
|
rows = <3>;
|
|
columns = <4>;
|
|
|
|
map = <
|
|
RC(0,0) RC(0,1)
|
|
RC(0,2) RC(0,3)
|
|
>;
|
|
};
|
|
|
|
kscan_matrix: kscan_matrix {
|
|
compatible = "zmk,kscan-gpio-matrix";
|
|
wakeup-source;
|
|
|
|
diode-direction = "col2row";
|
|
|
|
col-gpios
|
|
= <&arduino_header 10 GPIO_ACTIVE_HIGH>
|
|
, <&arduino_header 9 GPIO_ACTIVE_HIGH>
|
|
;
|
|
|
|
row-gpios
|
|
= <&arduino_header 13 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>
|
|
, <&arduino_header 11 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>
|
|
;
|
|
|
|
};
|
|
|
|
kscan_direct: kscan_direct {
|
|
compatible = "zmk,kscan-gpio-direct";
|
|
wakeup-source;
|
|
status = "disabled";
|
|
|
|
input-gpios
|
|
= <&arduino_header 10 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>
|
|
, <&arduino_header 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>
|
|
, <&arduino_header 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>
|
|
, <&arduino_header 11 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>
|
|
;
|
|
|
|
};
|
|
|
|
kscan_sp3t_toggle: kscan_sp3t_toggle {
|
|
compatible = "zmk,kscan-gpio-direct";
|
|
toggle-mode;
|
|
|
|
input-gpios
|
|
= <&arduino_header 4 GPIO_ACTIVE_LOW>
|
|
, <&arduino_header 3 GPIO_ACTIVE_LOW>
|
|
, <&arduino_header 2 GPIO_ACTIVE_LOW>
|
|
;
|
|
};
|
|
|
|
encoder: encoder {
|
|
steps = <80>;
|
|
compatible = "alps,ec11";
|
|
a-gpios = <&arduino_header 15 GPIO_PULL_UP>;
|
|
b-gpios = <&arduino_header 14 GPIO_PULL_UP>;
|
|
};
|
|
};
|